The Control System has Scimens PLC and Touch Screen.

This Booster Pump water intake from raw water tank, enter into Sand/ Carbon Filter with automatical controller, and softener with generation brine tank refill, the softener will be used for raw water with high hardness, The effluent from Softener then enter into cartridge filter with 5micron as good pretreatment of RO system.

The frist stage RO high pressure pump, with 1.3MPa working pressure, 2 units brackish RO 8040 Membrane, design recovery rate at 70%, that the capacity will be around 1.4m3/Hour.

Hinada is the leading manufacturer of RO System and High purity EDI System.

The 2nd stage RO System, high pressure pump, with 1.1MPa working pressure, 2 units low pressure RO 8040 Membrane, design recovery rate at 90%, that the capacity will be around 1.26m3/Hour, and the concentration water can return to 1st RO System input raw water tank.

The EDI System for making high purity water, the EDI feed water Conductivity: ≤10μ S/cm, and resistivity of permeate water ≥15.2MΩ.cm, the concentration of EDI system can return to 1st RO System tank.

The post 2 stage RO System with EDI System for Cosmetics factory application appeared first on Hinada.

Today, we will briefly introduce the EDI Pure Water System, which will ship to Russia, with a capacity of 30m³/Hour.

It has 6 sets of 5m³/hour EDI Modular, the Maximum design flow rate can be 6m³/hour for each EDI Modular.

This is the Control Panel of this EDI System, the Indicators A, B, and C show 3 phases of input Power. If any of the indicators, not lightning, that’s means phase loss.

This input water Conductivity Meter, the right one is Permeate Resistivity Meter.

This No#1—6 EDI Controller Button and Power Voltage.

Those buttons for operating and controlling this EDI System.

The first one is Emergency Stop; it can work as the main switch, during the working time, the button should be open; if the EDI System is closed, this button should be in an off state.

The second button is Booster Pump, the third button is Chemical Clean Reflux Valve.

The fourth Button is the High-Pressure Alarm,

This input water tank Water Shortage indicator

The clean water tank High Water Level indicator

This Lines button is NO #1—6 EDI Controller,  Start and Stop Button.

Firstly, open the booster pump button, then open those NO#1—6 EDI Controller buttons, and open the Main Switch. Then will automatically start running, and check the conditions, this Water Shortage Indicator on that’s meaning input water tank shortage of water, for this test we give it a high water level signal,  The Booster, and Inlet water Valve will start and run it, and the whole system will run it.

The whole EDI System treatment process is from the Booster pump to a cartridge filter and enters the 6 EDI Modulars.

We come to check the flow meters, the concentration meter is around 400L/H, Pure water flow meter design at 5—6m3/hour, and the whole EDI System Permeate Flow meter is around 35m3/hour.  The concentration flow meter is around 2.4m3/hour.

The Inlet pressure at 0.2MPa.

The Inflow Conductivity Meter is at 0.62 us/m, Permeate Resistivity Meter is at 18.2 Ω

This the controller No #1—6,  Electric Current and Voltage, normally the Electric Current set at 2—3Am, if water quality very good choose 2Am, If water quality not good choose at 2.5—3Am.

30m3 per hour EDI System pure water filtration operation, Any further questions just let us know.

The post 30m3 per hour EDI System pure water filtration operation appeared first on Hinada.

The post Purified Water System RO Plant and EDI appeared first on Hinada.